###
DOI:
工程科学与技术:2015,47(1):192-199
←前一篇   |   后一篇→
本文二维码信息
码上扫一扫!
响应面分析法优化太湖原水作为水厂水源的预处理工艺
(1.同济大学 污染控制与资源化研究国家重点实验室;2.无锡自来水总公司)
Optimization of Pre-treatment of Taihu Lake Water with Response Surface Methodology
(1.State Key Lab.of Pollution Control and Resource Reuse,Tongji Univ.;2.Wuxi Water Works Co.,Ltd.)
摘要
图/表
参考文献
相似文献
本文已被:浏览 1737次   下载 1
投稿时间:2014-06-08    修订日期:2014-07-03
中文摘要: 针对太湖水质,采用响应面法(RSM)优化臭氧-混凝工艺。在单因素试验的基础上,选取臭氧(O3)投加量、混凝剂投加量和停留时间为影响因子,CODMn去除率、浊度去除率和运行成本为目标响应,利用Box-Benhnken design(BBD)进行3因素3水平实验设计,研究各自变量间的单独与交互作用及对响应值的影响。根据拟合的线性二次回归方程得到臭氧-混凝的最佳工艺条件为:以硫酸铝作混凝剂时,O3投加量0.9 mg/L,混凝剂投加量35 mg/L,接触时间17 min;以聚合氯化铝作混凝剂时,O3投加量0.9 mg/L,混凝剂投加量24 mg/L,接触时间17 min。该条件下可使臭氧-混凝过程中CODMn和浊度的去除率达到最大,同时运行成本费用最低。
中文关键词: 预臭氧  混凝  BBD  响应面分析法
Abstract:Response surface methodology(RSM) was applied for optimizing the enhanced coagulation process by preozonation for Taihu lake water.Based on single-factor experiments,three independent variables(ozone dosage,coagulant dosage and residence time) were selected as affecting factors and three dependent variables(chemical oxygen demand(CODMn) removal efficiency,turbidity removal efficiency and operating cost) as responses.An experimental design of three factors and three levels was arranged through Box-Benhnken design (BBD).According to the proposed quadratic models,maximal CODMnand turbidity removal efficiencies and minimal operating costs are obtained at following optimum condition:The ozone dosage,coagulant dosage and residence time are found to be 0.9 mg/L,35 mg/L and 17 min for aluminum sulfate(AS) and 0.9 mg/L,24 mg/L,and 17 min for polymerization aluminum chloride(PAC),respectively.
文章编号:201400604     中图分类号:    文献标志码:
基金项目:国家自然科学基金资助项目(2012ZX07403-001;2008ZX07421-002;51178321);高等学校博士点基金资助项目(20120072110050);住房和城乡建设部研究开发项目资助(2009-K7-4)
作者简介:
引用文本:
殷娣娣,高乃云,高梦鸿,戎文磊,周圣东,陆纳新.响应面分析法优化太湖原水作为水厂水源的预处理工艺[J].工程科学与技术,2015,47(1):192-199.
Yin Didi,Gao Naiyun,Gao Menghong,Rong Wenlei,Zhou Shengdong,Lu Naxin.Optimization of Pre-treatment of Taihu Lake Water with Response Surface Methodology[J].Advanced Engineering Sciences,2015,47(1):192-199.