Effects of Tooth Slotting on Mechanical Properties of Filtering Reducer

doi:10.15961/j.jsuese.2014.05.055

您当前的位置：

首页 >

文章列表页 >

Effects of Tooth Slotting on Mechanical Properties of Filtering Reducer

更新时间：2023-11-14

- Effects of Tooth Slotting on Mechanical Properties of Filtering Reducer
- Advanced Engineering Sciences Vol. 46, Issue 5, Pages: 168-174(2014)
- 作者机构：
  
  1. 四川大学制造科学与工程学院四川大学空天科学与工程学院
  2. 四川大学制造科学与工程学院
  3. 四川大学空天科学与工程学院
- 作者简介：
- 基金信息：
- DOI：10.15961/j.jsuese.2014.05.055
  CLC：
- Published：2014，
  
  Published Online：16 May 2014，
扫描看全文
王家序,汪正炜,蒲伟,周广武,何涛,张渝爽.齿上开槽对滤波减速器力学性能的影响[J].工程科学与技术,2014,46(5):168-174.

Effects of Tooth Slotting on Mechanical Properties of Filtering Reducer. [J]. Advanced Engineering Sciences 46(5):168-174(2014)
王家序,汪正炜,蒲伟,周广武,何涛,张渝爽.齿上开槽对滤波减速器力学性能的影响[J].工程科学与技术,2014,46(5):168-174. DOI： 10.15961/j.jsuese.2014.05.055.

Effects of Tooth Slotting on Mechanical Properties of Filtering Reducer. [J]. Advanced Engineering Sciences 46(5):168-174(2014) DOI： 10.15961/j.jsuese.2014.05.055.

摘要

中文摘要: 使用有限元法研究滤波减速器轮齿上开槽对滤波减速器轮齿的动力学性能和传动性能的影响。通过对滤波减速器齿上不同开槽形状进行有限元对比分析，结果显示直槽对轮齿力学性能有很好的改善作用。在此基础上分析了直槽的槽深、槽宽、应力释放孔大小和应力释放孔与直槽的倒角大小对轮齿力学性能的影响以及不同载荷下轮齿应力分布情况。研究结果表明:在滤波减速器齿上开直槽，当槽深大于轮齿模数的3倍，应力释放孔和倒角的半径大于槽宽的10倍，槽缝宽度不超过轮齿模数的1/10时，其接触应力、弯曲应力和冲击振动较小。

Abstract

Abstract:The influence of slotting on the mechanical properties and transmission performance of gear teeth of filtering gear reducers was studied through finite element method.According to the comparative results of different slot shapes

it is found that straight slot has very good effect on mechanical properties of the gear tooth.Then the influence of slot depth

pore size

stress release hole and the chamfer size was analyzed

cases with different applied loads were also simulated.Finally

the results showed that the straight slot on Filtering Gear Reducer when its depth is three times bigger than the modulus of the teeth

the radius of stress release hole and the chamfer are both ten times bigger than the pore size，and pore size is smaller than ten percent of the modulus of the teeth

can effectively improve the mechanical properties of the tooth and reduce the vibration caused by gear meshing.

关键词

齿上开槽槽型接触应力弯曲应力有限元法

Keywords

slotting on the gear teethslot profilecontact stressbending stressfinite element method

references

更多指标>

Views

下载量

CNKI被引量

Alert me when the article has been cited

提交

Tools

Publicity Resources

Accurate Finite Element Modeling and Validity Analysis of Thread Structure

Non-Hertzian Contact Stress Calculation of High-speed Ball Screw Mechanism

Analysis Method of Bearing Capacity of Stud Connector in Steel-concrete Composite Structures Under Push-out Failure

Related Author

No data

Related Institution

Inst. of Defense Eng.,, PLA, Beijing

Security and Protection Dept. of Public Security Ministry

Beijing Key Lab. of Advanced Manufacturing Technol., Faculty of Materials and Manufacturing, Beijing Univ. of Technol.

Beijing Key Lab. of Electro-Machining Technol.

Inst. of Standard Metrology, Chinese Academy of Railway Sciences

⁰